Troubleshooting
Look in the log first: EDGEfab: Show Log in the command palette (Ctrl+Shift+P). It lists every step with file paths, and says why something failed.
Keys
| You see |
Do |
| A key is refused as you type it |
A Tripo key starts with tsk_, an OpenAI key with sk-. Paste the whole key, with no spaces |
| “OpenAI refused the key” or Tripo refuses it |
The key is wrong, revoked or switched off. Make a new one and set it again |
| EDGEfab uses a different key than the one you set |
TRIPO_API_KEY or OPENAI_API_KEY is set in Windows, and that one wins. Remove the variable, or change it |
| EDGEfab asks for the key again after Clear |
That is what Clear does. Set it again |
Pictures and models
| You see |
Do |
| A picture has the wrong thing on one side |
Change it: “put the keypad on the right side”. Or Draw Picture with the whole object described again |
| A change altered more than you asked |
Go back to the earlier picture in the history and ask again, with one change at a time |
| OpenAI or Tripo refuses the words |
The service’s content rules stopped it. EDGEfab says so in plain words. Reword it |
| Tripo says there are not enough credits |
Top up at Tripo. EDGEfab shows your balance before each model |
| The model looks worse than the picture |
Check all four views of the picture first: the model follows them. Then try High detail, or another picture |
| The model is far too big or small |
Set Size… on the Desk |
| Size unknown on the Desk |
Tripo gives no size for models in parts. Set Size… |
| Panels ripple |
That is Tripo’s detailed shape. Use Detailed texture instead of High detail |
| A part is missing or see-through from behind |
Say so in an issue, with the model. EDGEfab adds back faces to open parts, and drops small loose pieces |
| The glow caught paint that isn’t a light |
Make the Painted Lights Glow… again with A few lights |
| The glow barely shows in the game |
Glow Strength…, a step up. Then Add to Project again |
| Making a model takes more than ten minutes |
Tripo may be busy. The progress note’s Cancel stops the wait |
The 3D view
| You see |
Do |
| “EDGEfab shows models in REDcode’s 3D view” |
Install REDcode, or press Open Preview for Tripo’s picture |
| “this prop has no model to show” |
The prop is still a picture, or its model file is gone. Make it 3D |
The tab is named view.glb |
That is the file the view opens. A tab that says the prop’s name is asked of REDcode |
| The model shows grey |
The view opened the game’s model, which carries no textures. Open it from the Desk, not from the file |
The Desk and Rename
| You see |
Do |
| “Could not move … something has it open” |
The prop’s 3D view or one of its files is open in another VS Code window. Close it there and rename again. EDGEfab closes the tabs in its own window, but can’t reach another window’s |
| The Desk doesn’t show something an assistant made |
Press Refresh at the top of the Desk |
| A deleted prop is still in a project |
Delete removes it from the Desk only. Delete its folder from the project too |
Add to Project
| You see |
Do |
| It asks for a project |
No project is open in REDcode. Open one, or pick the project’s folder |
| “is not a WolvenKit project” |
Pick the folder that holds the .cpmodproj file |
| REDbridge can’t start, or the game isn’t found |
Set REDcode up first: REDcode: install. EDGEfab uses REDcode’s game folder and REDbridge |
| It takes minutes |
Normal the first time for a prop in parts: about four textures are made for each part. Adding it again keeps the unchanged ones and is much faster |
| A part lost the material you gave it |
You pressed Start Over…, or the prop was renamed: a new name is a new prop in the project. Give the part its material again |
| A material is listed as missing in the log |
That part keeps a plain look. Say so in an issue, with the log |
| After a rename, the project has the prop twice |
The new name is a new folder. Delete the old one from the project |
In the game
| You see |
Do |
| The prop isn’t in EDGEbuilder’s Mods tab |
Wait a few seconds, or close and open Assets. Check that the mod was packed and installed, or swapped in |
| “Restart the game to see the change” after Pack and Play |
REDnode’s MCP server is off, or the game isn’t running with REDnode. Turn it on in REDnode’s settings and press Pack and Play again |
| V walks through the prop |
The Collision setting is none. Set it to physical and Add to Project again |
| The prop faces sideways |
Only Tripo’s models are turned. For a model of your own, turn it in your 3D program and import it again, or turn it with EDGEbuilder |
| Raised details look like dents |
Not expected: EDGEfab writes bumps the way the game reads them. Say so in an issue |
| The lights are dark at night |
Tripo’s lights are painted. Use Make the Painted Lights Glow |
| It sinks into the ground or floats |
Move it with EDGEbuilder. EDGEfab stands the model on its lowest point |
The Library
| You see |
Do |
| “no EDGE Library is set up yet” |
Set Up the Library… in the Library view |
| “The Library’s folder is missing” |
The folder was moved or its drive is off. Bring it back, or Set the Library Folder… |
| Add to Library stops at the size |
Set Size… first |
| A prop’s name is taken |
Two Library props can’t share a game name. Rename the one on the Desk |
| A project doesn’t get the newer version |
Refresh Project from Library…, tick it, then pack again |
Assistants
| You see |
Do |
Claude doesn’t see the fab_ tools |
Start a new Claude Code session after connecting. Run claude mcp list: edgefab should show as connected |
| “claude command isn’t on the PATH” |
EDGEfab couldn’t run Claude Code. Press Copy the Command and run it in the terminal where claude works |
| “No OpenAI API key” or “No Tripo API key” |
The server reads Windows’ environment variables. Set them, then close every VS Code window and open it again: see Keys for the server |
| The key is set, and still “No … API key” |
A VS Code window was left open, so the program never restarted. Close them all. Check in Task Manager that no Code.exe is left |
| “OpenAI refused the key” |
The variable holds a wrong or revoked key. If the buttons in EDGEfab work, that key is good: use the same one |
| Every EDGEfab tool shows twice |
EDGEfab is connected twice. Run claude mcp list and remove one with claude mcp remove edgefab |
| Claude made a prop but the Desk is empty |
Press Refresh on the Desk. If it is still empty, the server may use another data folder: check the folder it names in its answer |
Still stuck
Ask on the EDGEmodders Discord, or open an issue. Say what you did and what you saw, and paste the lines from Show Log. Check them for your Windows user name in paths before you post.
Last reviewed 2026-11-17. Something wrong or missing? Tell us on Discord or open an issue.